CEO Atomizer MT Essentials

MT Essentials, a brand managed by skilled Croatian manufacturer Van&Del Design in collaboration with famous reviewer Mark Todd, is proud to offer the CEO, an atomizer with a very particular design, specially made for the Boro connector Billet Box, but any e-cig device with 510 connector!

In particular, the CEO atomizer offers a clever single coil deck, a 4ml PC 1000 tank and an air intake system specially designed for restricted direct inhaling (RDL) that you can switch to indirect inhaling (MTL) vape thanks to the provided airflow insert!

N.B: The CEO cannot be combined with any Billet Box. You need to check if yours is fitted with a Boro connector; if this is the case, you can already use it with Boro Tank atomizers (the R4 for example).

A special Boro Box atomizer that looks like a RBA cartridge

Despite its rock-like look, the CEO atomizer turns out to be absolutely charming. Indeed, behind its raw rectangular appearance, 40mm long, 26mm wide, and 17mm deep, this beautiful atomizer offers a unique, refined, and straightforward design with perfectly machined details.

Compatible with all electronic cigarettes thanks to its 510 connector, the CEO atomizer is specially made for Billet Box mods fitted with a ‘Boro’ connector, meaning all those already using Boro Tank atomizers!

To integrate your beautiful CEO inside a Boro connector Billet Box:

1. Access the inside of your Billet Box
2. Place the air slot/chimney under the CEO atomizer, close to the 510 pin
3. Remove the drip tip
4. Insert the CEO in the provided slot of your Billet Box
5. Screw the drip tip on the top of your Billet Box

N.B: The drip tip is not included in the CEO atomizer box.

The CEO atomizer by MT Essentials

The single coil deck you need: easy to build!

By simply unclipping the tank part of your CEO, you’ll access a very clever single-coil deck. It has been designed for beginners, and will also make experienced vapers’ life easier:

• Two slightly out-of-alignment posts facing each other, shaped like stairs, make the build extremely easy
• A large well, in which you will place the ends of your cotton wicks
• A small groove to accommodate the MTL airflow insert (included in the box)

The single coil deck of the CEO atomizer by MT Essentials

A unique air intake system with airflow insert

The airflow of the CEO is very specific, specially designed to perfectly combine with the Boro-type Billet Box.

Fitted on the front side, the small 5mm long, 1mm wide air intake doesn’t allow any adjustment. No need for an airflow ring! The CEO atomizer originally offered restricted direct inhaling (RDL) vape.

The air intake of the CEO atomizer by MT Essentials

Do you prefer a tighter vape? No problem! The CEO is delivered with THE piece you need: a PEEK airflow insert, specially designed for indirect inhaling (MTL) vape!

This small part offers three 0.6mm wide holes. Easy to install and to remove, it must be fitted directly on the side of the deck.

A high-quality and ingenious tank

Each part of this atomizer is cleverly designed, even in its smallest details. Benefiting from its ‘RBA cartridge’ aspect, the CEO offers a tank very ingenious for its size, material, capacity, and side fill system.

First asset: It is very resistant. Made from PC 1000 (polycarbonate), this tank is both high-quality and sturdy!

The second asset is its capacity. As it can contain up to 4ml, you’re sure not to run out of e-liquid for a while!

Finally, it is incredibly easy to fill! Simply lift the strip to cleanly and quickly fill the tank!

The side-fill system of the CEO atomizer by MT Essentials

Contents of the box of the CEO atomizer

• One CEO atomizer
• One PEEK airflow insert for MTL
• One air diffuser
• One Allen key
• One pack of spare joints and screws
• One user guide

The CEO atomizer is manufactured by Van&Del Design, in collaboration with Mark Todd for the MT Essentials series.

Contents of the box of the CE atomizer by MT Essentials