Lost Vape Centaurus G80 Kit

The brand Lost Vape presents an AIO kit in a small format of an electronic mod and a cartridge.

Functioning with an 18650 battery, the mod offers a power going up to 80W. It has a Quest 2.0 chipset and its Power and RBA modes.

The mod is matched with the UB AIO cartridge with a 5ml capacity. It works with UB Ultra coils, with two included in the box.

For rebuildable enthusiasts, you can add it a tank in a Centaurus Boro tank and proceed to your favorite builds.

Lost Vape's Centaurus G80 kit

The design of the Centaurus G80 kit

Despite its AIO format, this kit offers comfortable handling thanks to its round grip around the battery compartment but also dimensions of 82.5 x 47.3 x 31.2mm and a weight of 131g (without battery).

The front side is composed of:

• A Fire button
• A glimpse of the cartridge
• A 0.42" OLED screen
• Two setting buttons

Please note that except for the Fire button, all the elements are hidden under a magnetic panel allowing you to see the level of e-liquid left or avoid any unwanted pushes on buttons.

In the box, you'll find a 510 drip tip meant for a tight vape in MTL or slightly airy in RDL.

Handling of Lost Vape's Centaurus G80 kit

How does the Centaurus G80 work?

The brand Lost Vape is meant for intermediate users with this kit. Indeed, with its UB AIO cartridge, it allows you to benefit from an AIO format without having to worry about any build.

For more expert users, you can associate a Centaurus tank with the Boro format.

You'll find two functioning modes accessible by pushing 3 times on the same Fire button:

• Normal mode: the QUEST chipset will automatically define the power delivered according to the value of the coil installed in the UB AIO cartridge, please note that you can increase or lower the watts in the limit of the maximum power recommended for your coil
• RBA mode: you'll select this mode only if you choose a Boro RBA tank (rebuildable). Careful, this setting doesn't adapt the power automatically, you have to define it yourself (from 5 to 80W) according to the type of coil wire used in your build

You access these settings by browsing through the 0.42" OLED screen and accessible setting buttons by taking the clear magnetic panel off.

The 0.42" screen of Lost Vape's Centaurus G80 kit

A supply in 18650 single battery

In order to supply your vape with all its energy, you'll need to accompany this kit with an 18650 battery (not included).

To insert it, remove the ribbed magnetic panel, allowing you to customize the design of your mod according to the battery wrap you've chosen. Then simply refer to the polarity indications on the bottom of the cover.

The 18650 single battery compartment of Lost Vape's Centaurus G80 kit

 A USB-C recharging port

In case you forget to recharge your battery and you still need to vape it, find a USB-C port below the mod.

In the box of this kit, you'll benefit from a USB-C cable included. Note, however, that it is preferable to charge occasionally in this way, and to use a dedicated external charger.

The recharging USB-C port of Lost Vape's Centaurus G80 kit

The UB AIO cartridge

If you are not familiar with the rebuildable world and prefer the pre-made coils, then this cartridge is ideal. Indeed, it only works with the UB Ultra coils (0.15ohm and 0.2ohm) that you'll find in the box.

You'll choose between:

• 1 0.15ohm UB Ultra coil: to use between 60 and 80 watts for an airy draw
• 1 0.2ohm UB Ultra coil: to use between 40 and 60 watts for a more restrictive draw

The UB AIO cartridge of Lost Vape's Centaurus G80 kit

To proceed to the installation of the coil in the cartridge, follow the guide below:

1. Take the magnetic panel off the Centaurus G80
2. Take the drip tip out and unscrew the nut thanks to the key included
3. Take the cartridge out
4. Pull on the airflow wheel to take it off
5. Soak a new coil of some e-liquid drops and insert it into the compartment
6. Replace the airflow wheel
7. Fill the tank of e-liquid
8. Reposition the cartridge in its compartment

N.B: wait 5 to 10 minutes before vaping it so the new coil is correctly primed with e-liquid.

The airflow of the UB AIO cartridge

To adjust the air supply to your vape, the cartridge features a wheel beneath the tank.

As a reminder, the more open the holes, the greater the air supply and the more airy your vape.

The airflow wheel of Lost Vape's UB AIO cartridge

How to fill the tank?

With the UB AIO cartridge, you'll benefit from a 5ml tank and a filling system.

When it's time to fill up with e-liquid, all you have to do is:

1. Remove the magnetic panel concealing your tank
2. Lift the silicone tab on the front of the cartridge
3. Insert the tip of your bottle into the filling hole
4. Pour in your e-liquid
5. Carefully close the tab
6. Put the magnetic panel back in place

The filling of the UB AIO cartridge of Lost Vape's Centaurus G80 kit

Box contents

• 1 80W Centaurus G80
• 1 5ml UB AIO Cartridge (pre-installed)
• 1 0.15ohm UB Ultra Coil
• 1 0.2ohm UB Ultra coil
• 1 510 drip tip
• 1 key
• 1 USB-C recharging cable
• 1 user guide

The Centaurus G80 kit is made by Lost Vape. Warning, it is sold without batteries.

Box contents of Lost Vape's Centaurus G80 kit