Asmodus Minikin Podmod

Asmodus succeded in offering a compact and powerful podmod with a 2,000mAh capacity.

Its built-in battery can be recharged by USB-C and has an OLED screen giving you access to the power setting up to 50 watts.

The Minikin podmod has a cartridge with magnetic 2ml cartridge and is specially made to get the Minikin coils of Asmodus.

Accessible to vape beginners, this electronic cigarette will suit expert vapers looking for light, transportable, and performing equipment.

Asmodus' Minikin podmod

The mini Minikin kit

The Minikin podmod by Asmodus, it's a compact design made in aluminum alloy with dimensions of 84x41.5x24mm for a weight of only 102g.

The main side of the kit presents, from top to bottom:

• The Fire button
• The OLED screen
• The setting buttons
• The USB-C port

Apart from comfortable handling, the Minikin podmod will also easily slide into pockets or bags.

The Space Edition versions benefit from a triply anodized conception so the paint holds well.

Handling of Asmodus' Minikin podmod

A cartridge with a magnetic connection

Betting on a simple and intuitive functioning, Asmodus gave a magnetic connection cartridge to the Minikin podmod.

This 2ml tank can easily be clipped or unclipped which allows you to fill it easily but also to alternate the flavors of e-liquid in the middle of the day. Don't hesitate to get a spare empty cartridge right now.

The magnetic connection between the cartridge and the Minikin podmod by Asmodus

A use accessible to everyone

Push the Fire button 5 times to turn on or off your podmod.

Adjust the power (from 5 to 50W) with the OLED screen by using the setting buttons. You can vape by pushing the fire button while inhaling in the mouthpiece.

Note that the Minikin chipset presents an electronic safety restricting the power according to the value of the coil used.

The OLED screen of Asmodus' Minikin podmod

A 2,000mAh built-in battery

To enjoy your Minikin podmod all day long, Asmodus gave it a 2,000mAh built-in battery.

Once this latter is discharged, use the USB-C cable included in the box to fill it with energy. Connect it to the suited port located below the setting buttons.

The USB-C port of Asmodus' Minikin podmod

The Minikin cartridge

Taking a 2ml tank, the Minikin cartridge is specially made to hold the removable Minikin coils.

Note that the mouthpiece can be replaced by the drip tip included in the box of the podmod. The latter is particularly meant for a tight draw in indirect inhaling (MTL) contrary to the one pre-installed for a slightly more vape in restrictive direct inhaling (RDL).

The cartridge of Asmodus' Minikin podmod

The Minikin coils

Asmodus delivers its podmod with two Minikin coils to install in the empty cartridge.

Select the value that suits you among the two offering the kit:

• 1 0.8ohm Minikin coil: to use between 12 and 16W. Ideal for a rather tight draw in indirect inhaling (MTL). Suits to vaping with CBD or nicotine salt e-liquids
• 1 0.3ohm Minikin coil: to use between 40 and 45W. Perfect for a more airy vape in restrictive direct inhaling (RDL). Particularly suit e-liquids with a nicotine rate from 0 to 6mg/ml

After two to three weeks of use, the coil will start to show some signs of wear (loss of flavors, light burnt taste). It will be time to replace it with a new one.

For this:

1. Take the cartridge out of the magnetic base
2. Pull on the used coil to take it off
3. Soak a new coil with some drops of e-liquid
4. Insert it in its compartment
5. Replace the cartridge on its base
6. Fill it with e-liquid
7. Wait for some time before vaping it so the coil is correctly primed

An adjustable airflow

Accessible without having to disconnect the cartridge from the base, a strip will allow you to set the airflow. Free more or less airflow holes according to your vape preferences.

The more the airflow hole is open, the more the draw will be airy.

The airflow strip of the cartridge on Asmodus' Minikin podmod

A 2ml capacity in e-liquid

Once you've installed your coil, you'll have to fill the tank.

For this, take your e-liquid bottle, then:

1. Take the cartridge off the base
2. Lift the cover in the direction of the arrow
3. Insert your bottle tip in the filling hole protected by a silicon strip
4. Pour your e-liquid
5. Reconnect the cartridge from the podmod

Reminder: wait 5 to 10 minutes before vaping it if you use a new coil.

The filling of the cartridge from the Asmodus' Minikin podmod

Box contents

• 1 50W Minikin podmod
• 1 empty Minikin 2ml cartridge (pre-installed)
• 1 0.8ohm Minikin coil
• 1 0.3ohm Minikin coil
• 1 RDL drip tip
• 1 MTL drip tip
• 1 USB-C cable
• 1 user guide

The Minikin podmod is made by Asmodus.

Box contents of Asmodus' Minikin podmod